• 

  Aluminum 6061-T6; 6061-T651 - MatWeb

  Aluminum 6061-T6; 6061-T651 Categories: Metal; Nonferrous Metal; Aluminum Alloy; 6000 Series Aluminum Alloy. Material Notes: General 6061 characteristics and uses: Excellent joining characteristics, good acceptance of applied coatings.

  Читать далее
• 

  Plastic deformation of AA6061-T6 at elevated ... - ScienceDirect

  Feb 15, 2022 · The temperature-dependent work-hardening of AA6061-T6 aluminum alloy is investigated using a combined experimental-numerical approach. Uniaxial tension experiments are performed from room temperature to 500 °C, and the force-displacement curves up to fracture are established. Both the yield strength and the work-hardening …

  Читать далее
• 

  Microstructure and mechanical properties of Ti6Al4V/AA6061…

  Apr 25, 2021 · In this work, Mg alloy sheet (1.3 mm) clad with a thin Ti6Al4V sheet (0.35 mm) by inserting a thinner AA6061 Al alloy interlayer (0.25 mm) was successfully fabricated via hot roll bonding at 400 °C. The interfacial reaction layer after annealing and its effect on the mechanical properties of the roll-bonded Ti6Al4V/AA6061/AZ31 LMCs were ...

  Читать далее
• 

  A modified Johnson-Cook model of AA6061-O aluminum …

  Apr 20, 2020 · In this paper, specimens were first pre-stretched to different pre-strain coefficients (0, 0.4 and 0.8) under quasi-static tensile for AA6061-O aluminum alloy. Then, the specimens with different pre-strain coefficients were stretched by a high-speed tensile machine (HTM) at different strain rates (200 s− 1, 400 s− 1 and 600 s− 1). Digital image …

  Читать далее
• 

  Preparation of Ti/Steel composite plates with AA6061 as the ...

  May 15, 2024 · The thicknesses of Q235 steel, TA1 titanium, and AA6061 plate were 2 mm, 2 mm, and 0.8 mm, respectively. A wire brush with 3 mm diameter bristles was used to remove the raw contaminants and original oxide layer on the surface of the plate. While the AA6061 in the middle layer needs to be polished on both sides.

  Читать далее
• 

  Deformation behavior of convolute thin-walled AA6061-T6

  Oct 7, 2021 · During manufacturing thin-walled tubes using free bending forming (FBF) technology, defects such as wrinkling, cracking, and cross-section distortion are easy to exist due to various forming parameters' direct and indirect influence, which seriously influences the forming quality of the rectangular tubes. Thus, in this study, the finite …

  Читать далее
• 

  Comparative Study on Mechanical and Metallurgical Properties of AA6061 ...

  Jul 18, 2014 · AA6061–T6 (Al–Mg–Si) alloy is a precipitation hardening aluminum alloy. The major alloying elements are magnesium and silicon, which give superior mechanical properties to the alloy because of form...

  Читать далее
• 

  Microstructure and process characterization of laser-cold …

  Mar 26, 2013 · Fiber laser-cold metal transfer (CMT) hybrid welding of an AA6061 aluminum alloy thin sheet was carried out. The microstructure was analyzed by an optical microscope, scanning electron microscope, and energy-dispersive spectrometry. The cross-weld tensile strength and hardness were tested to evaluate the mechanical properties of …

  Читать далее
• 

  Effect of variants of gas metal arc welding process on tensile ...

  Jun 15, 2020 · This article describes the influence of gas metal arc welding (GMAW) variants on tensile properties of welded thin sheets of AA6061-T6 aluminium alloy. Single V butt joints were fabricated using the four variants of the GMAW process (constant current, pulsed current, cold metal transfer and pulsed cold metal transfer) under optimized …

  Читать далее

Соответствующая статья